Search:

Type: Posts; User: JoeySEI

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    298

    It sounds like you ordered the wrong shift plate....

    It sounds like you ordered the wrong shift plate.

    There are 2 different shift plates.

    1 comes with the switch normally open.

    1 comes with the switch normally closed.

    You ordered the one...
  2. Replies
    1
    Views
    234

    We can confirm that it will work, however, we...

    We can confirm that it will work, however, we can't comment on customers experience on the water using the CH1700. Hopefully some people that have used it in the past will reply to this post.
  3. Replies
    3
    Views
    298

    I just sent you an email with attached...

    I just sent you an email with attached Instructions.

    It will be from joey@sterndrive.cc

    Regards,

    Tech Support
  4. Thread: oil discharge

    by JoeySEI
    Replies
    1
    Views
    180

    I would recommend Pressure testing the drive if...

    I would recommend Pressure testing the drive if that looks good then oil shouldn't be coming from the drive.
  5. Replies
    3
    Views
    428

    The serial number is located inside the case so...

    The serial number is located inside the case so you have to take the boat out of the water and separate the units to see the red tag.
  6. Replies
    3
    Views
    428

    I’ve heard with a stainless steel prop hitting a...

    I’ve heard with a stainless steel prop hitting a rock can damage the outdrive. Whereas with an aluminum prop the prop will be damaged but may save the outdrive from damage. Is this true?

    Yes this...
  7. It sounds like you have the seal installed upside...

    It sounds like you have the seal installed upside down. When the seal is installed the spring should be pointed up. When that seal is installed the right way you then should be able to install the...
  8. Replies
    1
    Views
    728

    I would recommend doing a pressure test and...

    I would recommend doing a pressure test and removing the top cover and inspecting the gears in the upper.

    If everything looks good and there wasn't any water in the oil you should be okay with...
  9. Replies
    5
    Views
    925

    Yes the 1.47 are HD gears. For the old drive,...

    Yes the 1.47 are HD gears.

    For the old drive, the best way to find that noise is to disassemble the drive and inspect all of the bearings.

    Regards,

    Tech Support
  10. Thread: Upper Gear Set

    by JoeySEI
    Replies
    1
    Views
    577

    The nut is used to pull the bearing together to...

    The nut is used to pull the bearing together to preload them. It does not have a torque spec. When removing it you need to start over with the preload. remove and install the bearings and use the nut...
  11. Replies
    2
    Views
    760

    Normally our bearing is greasable but currently...

    Normally our bearing is greasable but currently we are selling it with the sealed bearing which is compatible with a greasable or sealed gimbal housing.

    Regards,

    Tech Support
  12. Your water pump is not compatible with our SE304...

    Your water pump is not compatible with our SE304 as it uses a different style key.

    The water pump kit you would need to order from us is part # 96-306-01K.

    I'm sorry if we didn't catch that at...
  13. Replies
    11
    Views
    8,122

    Please refer to the email we sent you on...

    Please refer to the email we sent you on 6-8-2018.

    Regards,

    Tech Support
  14. Replies
    1
    Views
    1,786

    It appears that part of the hole is missing. ...

    It appears that part of the hole is missing.

    Try using a weatherstrip adhesive to glue the seal down.

    Let it sit for 24 hours before installing it so it can dry and then fill it with gear lube...
  15. Good Morning, It sounds like this is something...

    Good Morning,

    It sounds like this is something that should be discussed over the phone.

    Please give us a call at (813) 925-7127 and ask for SEI Tech Support and we will assist you in installing...
  16. Thread: SE106 impeller

    by JoeySEI
    Replies
    4
    Views
    5,789

    Yes you need to put the lower unit in forward...

    Yes you need to put the lower unit in forward when taking the gear case off and that would be a good idea to monitor the temperature with the water jacket.

    Regards,

    Tech Support
    (813) 925-7127
  17. Replies
    1
    Views
    1,069

    Yes you can do that with no problem. SEI Tech...

    Yes you can do that with no problem.

    SEI Tech Support (813)925-7127
  18. Replies
    1
    Views
    2,501

    Good Morning, There is no spec for prop shaft...

    Good Morning,

    There is no spec for prop shaft end play. It's not something that you can adjust by shimming either.

    Are you having an issue with your prop shaft?

    Regards,
  19. Replies
    1
    Views
    1,768

    Good Afternoon, This is Joey from SEI. ...

    Good Afternoon,

    This is Joey from SEI.

    Please give us a call @ (813) 925-7127 and ask for Rob in Tech Support and he should be able to help you out with this.

    Regards,
Results 1 to 19 of 19

115 S. Forest Lakes Blvd.
Oldsmar, FL 34677

tel: 813.925.7127
fax: 813.925.7064


Sterndrive Engineering, Inc. (SEI) manufactures a stern drive designed to replace Mercury Marine's MerCruiserŽ Alpha OneŽ, R, MR, Gen II and Bravo OneŽ stern drives. MerCruiserŽ Alpha One, R, MR, Gen II and Bravo OneŽ are trademarks of the Brunswick Corporation. SEI has no affiliation with the Brunswick Corporation. Consequently, any warranties governing products and or sold by Brunswick Corporation will not apply to products manufactured and or sold by SEI, or to products damaged due to the operation of an SEI product.