Search:

Type: Posts; User: Bt Doctur

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    8,812

    You could take a 3/4 impact socket and cut...

    You could take a 3/4 impact socket and cut everything away with a die grinder cut-off wheel leaving the 2 legs
  2. Replies
    5
    Views
    3,866

    Being a GEN II type the bellows is glued and...

    Being a GEN II type the bellows is glued and clamped at the transom and has an inner ring that seals the gimbal housing side. Correctly installed should not leak. The think rubber ring in the...
  3. Replies
    3
    Views
    2,103

    give or take under 1 minute, less if the block...

    give or take under 1 minute, less if the block and manifolds are already full
  4. Replies
    3
    Views
    2,103

    The water will exit the reliefe ports the same...

    The water will exit the reliefe ports the same way, on a hose or on muffs. Check to make sure you have assembled it correctly, making sure the O rings are in the connector tube that accepts the...
  5. Replies
    1
    Views
    2,003

    Well, it gives you time to assemble it properly...

    Well, it gives you time to assemble it properly and fill it with oil. Now we have to wait for the ice to turn back into water
  6. Thread: Impeller

    by Bt Doctur
    Replies
    3
    Views
    3,229

    There is the rubber impeller that will show...

    There is the rubber impeller that will show visable damage, the top cover will show melted plastic on top just under the rubber slinger washer, the water pump base will show melting damage under the...
  7. Replies
    2
    Views
    5,949

    Big blocks and Alpha drive require a gentle hand...

    Big blocks and Alpha drive require a gentle hand on the throttle and a light boat to stay together.Friend had the BAHA24 Ft with the same package, Use a gentle hand untill your planed up and then go...
  8. Thread: Impeller

    by Bt Doctur
    Replies
    3
    Views
    3,229

    If you operated it proerly and if you didnt...

    If you operated it proerly and if you didnt damage it with sand or mud and if the oil is still clean and up to the full level then the normal schedule is 2 yrs of normal season use (roughly 100hrs...
  9. corrosion

    corrocion or electrolsys? You may have 12v leaking from the trim sender wiring/broken wiring, chafed wiring.
    If this is so, remove the trim sender wire at the front of the engine .If wish to use...
  10. That stud is not installed by the factory because...

    That stud is not installed by the factory because of damage during transit.You normally would take 2 nuts back to back and install the stud with a drop of blue loc-tite untill tight.
  11. Replies
    12
    Views
    5,543

    Did you check the lower with the muffs in my...

    Did you check the lower with the muffs in my earlier post before replacing the unit?
  12. Replies
    4
    Views
    3,363

    this was on a Black Max outboard

    http://i57.photobucket.com/albums/g219/BtDoctur/propshaft-1.jpg
    this was on a Black Max outboard that hit some rocks at full throttle.the crankshaft end was ripped off the crankshaft.
    with the...
  13. Replies
    6
    Views
    5,499

    the shift intereupt can be operated by hand to...

    the shift intereupt can be operated by hand to check the switch and associated wiring to confirm operation.
    switch never should move on land,only in the water with a load on the prop.
    And added...
  14. Replies
    12
    Views
    5,543

    no water should appear anywhere. not the slinger,...

    no water should appear anywhere. not the slinger, copper tube or base.water does not normally come out the top of the pump, it must be pumped out. will not show water on muffs. I`m betting there is a...
  15. Replies
    12
    Views
    5,543

    Have your mechanic drop the lower and apply muffs...

    Have your mechanic drop the lower and apply muffs to it. Betting you`ll find a leak at the water pump base section.
    still or slow the water pump housing is covered in water, at higher speed the...
  16. Replies
    10
    Views
    4,162

    does the switch when manually activated stall the...

    does the switch when manually activated stall the motor?
  17. Replies
    3
    Views
    3,000

    flushing, as in after each use

    Nothing for these drives except muffs or in water. A system can be constructed with some T`s and valves and a additional bilge hose fitting.PVC may also be used.
    you can pm me for my cell if I dont...
  18. Thread: stern drive

    by Bt Doctur
    Replies
    1
    Views
    2,943

    pins

    Alpha uses 1 cotter pin in the lower connecting pin.changing the housing has nothing to do with the swivel pin .Unless you have an early Series 1, MC-1 that uses SS nails to hold the hinge pins in...
  19. Thread: Se106 1:47

    by Bt Doctur
    Replies
    4
    Views
    2,619

    backfiring

    This would be an engine issue and has nothing to do with a drive.backfiring can be water, lean fuel mix, ethanol seperation, plugs, cap ,rotor,burned/tuliped valves.
    water ingestion can also come...
  20. Thread: sei 106

    by Bt Doctur
    Replies
    3
    Views
    5,029

    impellers

    Been doing warranty replacements on the impellers I`ve installed. Seems the company making them had changed manufactures and had this problem. They claim to have corrected it but there is still some...
  21. Thread: sei 106

    by Bt Doctur
    Replies
    3
    Views
    5,029

    damage

    Well, if they removed them and did an inspection ,what was the damage to the impellers? most shops would have simply replaced the impellers and had you on your way first.Then worry about a warranty...
  22. Replies
    3
    Views
    16,103

    switch

    I believe the roller coming out of the V groove should only move an 1/8th inch or so to stall the motor.There is an adjustment for the arm. You can verify this by backing the boat into the water but...
  23. Replies
    4
    Views
    2,367

    pump

    Impellers dont get damaged from sitting.must be some other cause .
    too little flow from a hose, over-reving on a hose, etc.A drive shower may have to be added to help cool the drive if you remove...
  24. Replies
    5
    Views
    5,940

    shaft

    nothing but a splined shaft that goes into the powerhead
  25. Replies
    4
    Views
    3,633

    Is this a cobra conversion? Only because you...

    Is this a cobra conversion? Only because you mention the ESA.
    Too high an idle wil make it difficult to shift properly.
Results 1 to 25 of 158
Page 1 of 7 1 2 3 4

115 S. Forest Lakes Blvd.
Oldsmar, FL 34677

tel: 813.925.7127
fax: 813.925.7064


Sterndrive Engineering, Inc. (SEI) manufactures a stern drive designed to replace Mercury Marine's MerCruiserŽ Alpha OneŽ, R, MR, Gen II and Bravo OneŽ stern drives. MerCruiserŽ Alpha One, R, MR, Gen II and Bravo OneŽ are trademarks of the Brunswick Corporation. SEI has no affiliation with the Brunswick Corporation. Consequently, any warranties governing products and or sold by Brunswick Corporation will not apply to products manufactured and or sold by SEI, or to products damaged due to the operation of an SEI product.