Search:

Type: Posts; User: bryboob

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    2,413

    adjust shift shaft without draining lube

    hi sorry to bother so much, is it possible to adjust the shift shaft without
    splitting the drive.
  2. Replies
    2
    Views
    2,695

    ok, I'll try that thanks again for your help, and...

    ok, I'll try that thanks again for your help, and sei has the best service and info. anywhere for
    all us do-it-your-selfer's .
  3. Replies
    2
    Views
    2,695

    clump, clump sound in lower

    hi all, removed bearing carrier and replaced prop shaft seals and big o-ring on
    bearing carrier, now I hear a clump, clump sound in lower only in reverse
    in forward sounds ok checked the shift...
  4. Replies
    4
    Views
    2,982

    thought I read that some where, kind of hard to...

    thought I read that some where, kind of hard to keep it away from the o-ring anyway

    thanks for the help
  5. Replies
    4
    Views
    2,982

    hi again, I finished replacing seals, O-rings and...

    hi again, I finished replacing seals, O-rings and already installed bearing carrier
    I have a question about perfect seal(92-34227-1) and the big o-ring behind the thrust washer
    just worried that I...
  6. Replies
    4
    Views
    2,982

    gear lube leak/ bearing carrier

    129hi again, posted here about a week ago about gear lube leaking at prop shaft
    I removed the lower half and also removed the bearing carrier, in the other
    post says if lube is in the exhaust...
  7. Replies
    5
    Views
    11,810

    thanks' for your help, if it is a very slow leak...

    thanks' for your help, if it is a very slow leak would it be ok to drive the boat for a few hours,because
    yesterday I filled it with gear lube and cleaned it up and I don't even have a drip ?
  8. Replies
    5
    Views
    11,810

    how to pressure test it? with what?

    how to pressure test it? with what?
  9. Replies
    5
    Views
    11,810

    haven't taken of the prop yet, just see it...

    haven't taken of the prop yet, just see it leaking behind the prop down the fin of the drive unit.
  10. Replies
    5
    Views
    11,810

    gear lube leaking from prop shaft?

    hi, boat has been sitting for 9 months now gear lube is leaking from prop shaft
    is there some sort of seal that needs to be changed and how to do it? (se106)
  11. Replies
    4
    Views
    2,501

    i only had it at idle and it burned,my brother...

    i only had it at idle and it burned,my brother has a
    volvo penta setup and he has a crank/cam driven
    water pump he's started his up a few times without
    water and his pump has never burned and he's...
  12. Replies
    4
    Views
    2,501

    hi, i checked the hose from the transom to...

    hi, i checked the hose from the transom to thermostat housing
    i blew thew it and water came out of it, and i checked for any
    kinks in the hose's and found nothing, because that was my first ...
  13. Replies
    4
    Views
    2,501

    cam driven raw water pump

    hi everyone, going to change to a cam driven raw water pump
    the pump in my se106 keeps going out, and not when i'am in
    the water it's when the boat sits, the first one i burned (no water)
    the...
  14. Replies
    1
    Views
    2,450

    growling sound when throttleing

    hi, have a growling sound when i punch thottle up and down
    and the growling sound is after i punch it like something is
    still turning fast after idle goes down, almost like the gimble
    bearing is...
  15. Replies
    4
    Views
    2,934

    yes, comes out of the bearing and still a little...

    yes, comes out of the bearing and still a little
    at the bottom of the tolerance ring.
  16. Replies
    4
    Views
    2,934

    i only pumped about 5 times and than stoped when...

    i only pumped about 5 times and than stoped
    when i saw it comeing from the bottom,
    where on the bearing should it come out?
  17. Replies
    4
    Views
    2,934

    grease from tolerance ring?

    hi, was greaseing gimble bearing and saw grease come
    from bottom of tolerance ring, is that normal or could
    the gimble bearing be pushed in to far passing the
    the gimble houseing grease hole? i...
  18. Replies
    2
    Views
    2,157

    broken bolt

    hi, yes it bolts in from bottom don't know how i broke it
    it's supose to be stainless steel and the unit is aluminum
    i even sprayed it with wd 40 before it turned it, there was
    no sign of...
  19. Replies
    2
    Views
    2,157

    broken bolt in upper?

    hi, was servicing my se106 and broke a bolt in the upper unit
    i know i need to tap it out, but i was wondering if i could do without
    it, it's a allen wrench bolt, there are two bolts in front and...
  20. Thread: no forward?

    by bryboob
    Replies
    3
    Views
    1,843

    new complete drive

    installed a new complete drive i think it's the shift shaft
    just hope i don't have to completly split the drive to
    adjust it .
  21. Thread: no forward?

    by bryboob
    Replies
    3
    Views
    1,843

    no forward?

    hi, my 106 drive won't go forward, took my boat to the water
    gets reverse and neutral but won't go forward just hear
    clinging sound when in forward could it be sift shaft not
    aligned right, and...
  22. Replies
    1
    Views
    1,623

    new drive not pumping water?

    hi again, i installed my new se106 drive but when i
    ran my boat at idle was not pumping water to my engine
    even took the hose that comes from the drive to my water
    pump off and no water is...
  23. Replies
    3
    Views
    2,336

    oil won't come out top?

    hi, i drained drive overnite , but when i try to fill from
    the bottom the oil keeps coming from the bottom and
    nothing from the top and half of the oil is in my drain
    pan, is there a special pump...
  24. Replies
    3
    Views
    2,336

    filling unit with gear lube

    hi, have a new complete se106 drive how do you fill
    the lower unit the screw hole is at the bottom so when
    i pump lube in (2 pumps) it comes back out. i filled the
    upper first, but when i open the...
Results 1 to 24 of 25

115 S. Forest Lakes Blvd.
Oldsmar, FL 34677

tel: 813.925.7127
fax: 813.925.7064


Sterndrive Engineering, Inc. (SEI) manufactures a stern drive designed to replace Mercury Marine's MerCruiserŽ Alpha OneŽ, R, MR, Gen II and Bravo OneŽ stern drives. MerCruiserŽ Alpha One, R, MR, Gen II and Bravo OneŽ are trademarks of the Brunswick Corporation. SEI has no affiliation with the Brunswick Corporation. Consequently, any warranties governing products and or sold by Brunswick Corporation will not apply to products manufactured and or sold by SEI, or to products damaged due to the operation of an SEI product.